Set the Power Logger up in seconds with the included flexible current probes and color display. The power quality meter measures most electrical power parameters, harmonics, and captures voltage events. Load studies - verify electrical system capacity before adding loads.
Energy assessments - quantify energy consumption before and after improvements to justify energy saving devices. Harmonics measurements - uncover harmonic issues that can damage or disrupt critical equipment.Voltage event capture - monitor for dips and swells that cause spurious resets or nuisance circuit breaker tripping. Record power and associated parameters for up to 45 days. Monitor maximum power demand over user-defined averaging periods. Prove the benefit of efficiency improvements with energy consumption tests. Measure harmonic distortion caused by electronic loads. Improve reliability by capturing voltage dips and swells from load switching. Easily confirm instrument setup with color display of waveforms and trends. Measure all three phases and neutral with included 4 flexible current probes. View graphs and generate reports with included Power Log software. Compact, rugged design with IP65 case, 600 V CAT III. ¼ VGA Graphic Color transmissive displays 320 x 240 Pixel with additional background lighting and adjustable contrast, text and graphics in color. Developed, designed and manufactured according to DIN ISO 9001. 4 MB Flash memory, 3.5 MB for measuring data. RS-232 SUB-D socket; 115.2 k Baud, 8 data bits, no parity, 1 stop bit, firmware updates are possible with the RS- 232 interface (9-pole extension cable). 50 Hz or 60 Hz, user-selectable, with automatic synchronization. NiMH battery-pack, with ac adapter (15 V to 20 V / 0.8 A). Typical > 12 hours without backlight and > 6 hours with backlight high. 240 x 180 x 110 mm. 1.7 kg, including battery. The above terms are defined in European Standards. To calculate the specification at any point in the working temperature range, use the temperature coefficient below.
±0.1% of the measured value per°C from the reference. Refers to reference temperature, maximum deviation is guaranteed for two years. Refers to operating temperature range, maximum deviation is guaranteed for two years.C1 (IEC 654-1) -5°C to +45°C, 5% to 95% RH, no dew. Cycoloy shock and scratch proof thermoplast V0-type (non-flammable) with rubber protection holster. IEC/EN 61326-1:1997 class B. IEC 61010-1 600 V CAT III, double or reinforced insulation, pollution degree 2. IP65; EN60529 (refers only to the main housing without the battery compartment).
RMS values are measured with a 20 ms resolution. 57 V/66 V/110 V/120 V/127 V/220 V/230 V/240 V/260 V/277 V/347 V/380 V/400 V/417 V/480 V AC. ±(0.2% of measured value + 5 digits). 100 V/115 V/190 V/208 V/220 V/380 V/400 V/415 V/450 V/480 V/600 V/660 V/690 V/720 V/830 V AC. 15 A/150 A/3000 A rms (at sine).
150 A/3000 A and 1 A/10 A. The errors of the current probes are not considered. When using Flexi Set please make sure to position the conductor opposite to the Flexi Set-lock. Power measurement P - Active, S - Apparent, Q- Reactive, D - Distorting. See V rms and A rms measurement.
Power errors are calculated by adding the errors of voltage and current. Additional error due to power factor PF. Specified error x (1-[PF]). Maximum range with voltage range 830 V delta-connection and 3000 A current range is 2.490 MW, higher displayed values possible when using PTs and CTs with ratio feature. Typical range with voltage range 230 V wye connection and 150 A current range is 34.50 KW.
1 W to 10 W. The errors of the current sensors themselves have not been considered. Energy measurement (kWh, KVAh, kVARh). + F variation error + 15 digit. + F variation error1 + 20 digit.0.000 to 1.000. 46 Hz to 54 Hz and 56 Hz to 64 Hz.
IEC 61000-4-7:2002, Class II. For THD 3% ±5% at Vnom. For THD 10% ±5% at Inom. Vm and Im are measured values of harmonic m. Detection of voltage dips, voltage swells and voltage interruptions with a 10 ms resolution and measuring error of the half period sine wave of rms.We are extremely busy, so we might not answer your emails. Items will be replaced or exchanged in case of DOA. All packages will go out after the weekend or after the holidays.
The item "FLUKE 1735 3 THREE PHASE POWER QUALITY LOGGER ELECTRICAL ENERGY ANALYZER" is in sale since Saturday, April 17, 2021. This item is in the category "Business & Industrial\Test, Measurement & Inspection\Testers & Calibrators\Calibrators\Pressure Calibrators".The seller is "computer_psycho" and is located in Van Nuys, California. This item can be shipped worldwide.